Jump to content
模组网
猫又~~

【书籍搬运】Heavy Armor Forging 重甲锻造

Recommended Posts

原文地址:http://www.uesp.net/wiki/Skyrim:Heavy_Armor_Forging

重甲锻造

作者:斯文·双锤

重甲必须专门为承受大量攻击而设计。在保护穿戴者之时,重甲将承受各种武器的直接打击。皮条在各类铠甲中都用于制作皮带和做捆绑固定之用。

铁和钢较为容易制作。只需要将其加热熔化然后锤炼成形。熔炼时的温度并不是那么重要。注意避免将金属锉光。尽量节约和保留金属,以便于将余料重新熔铸。

铁甲需要大量的铁锭。一名铁匠一般需要两打数量的铁锭来完成全套铁甲制作。钢甲主要需要钢锭,不过也需要使用一些铁锭。

矮人铠甲使用来人金属制造。这种材料的秘密随着矮人千年前的消失而失传了。现在只能在矮人遗弃的城市和堡垒中发现这种材料的碎片了。

兽人铠甲需要大量的山青铜,同时混合少量的铁。加热过程需要保守一些以使其变脆。兽人是这项技艺的大师,不过只要有耐心和技巧,任何一名铁匠都能够掌握。

钢制板甲的制作需要向钢材中掺入金刚砂。这种合金强度比两种原材料本身还要高。金刚砂是一种在熔炼到稳定成型过程中对加热要求很苛刻的材料,并且也不是非常常见。

玄铁只能在加热以后才能加工。如果未经加热就锤炼的话,这种材料会产生细小的裂缝,最终使材料整体碎裂。与其他铠甲制作不同,玄铁不能与铁掺和,必须保持纯净。

对于如何制作迪德拉铠甲,我只能给你讲些故事了。我自己从来没亲眼见过,也不知道有谁拥有过。传说这种铠甲只能在晚上加工……想要完美的话还需要在新月或者满月时,也不能在月食的时候。一轮红色的丰收满月据说是最好的。玄铁是基本材料,不过必须在合适的时候向火种投入一枚迪德拉之心。

Share this post


Link to post
Share on other sites

Heavy Armor Forging
by Sven Two-Hammers
A guide to creating Heavy Armor


Heavy armor must be designed to take a lot of punishment. It will receive direct blows from all sorts of weapons while protecting the wearer. Leather strips are used to make the straps and bindings in all armor.
Iron and steel are easy to work. Just heat them up and pound them into shape. The heat of the forge is not that critical. Avoid filing off any of the metal. Always try to conserve the metal and work it back into shape.
Iron armor requires a large number of iron ingots. A smith might need a couple of dozen to complete a full set of iron armor. Steel armor primarily uses steel ingots, but some iron is used as well.
Dwarven armor is made from dwarven metal. The secret of this material was lost when the dwarvesdisappeared millennia ago. Now it can only be found as scrap in the ruins of their abandoned cities and fortresses.
Orcish armor requires large amounts of Orichalcum, melded with a bit of iron. Heat should be used sparingly, lest it become brittle. The Orcs are masters of this technique, but it can be learned by any smith with patience and skill.
Steel plate mail is made by adding steel to molten Corundum. The alloy is stronger than either metal by itself. Corundum is a finicky material requiring the heat from the forge to be steady and not vary much.
Ebony can only be worked when heated. It will develop small cracks that eventually shatter the material if hammered cold. Unlike most other armors, Ebony will not alloy with iron. It must be used pure.
I can only tell you tales of how to make Daedric armor. I have never seen it myself, nor do I know anyone that has. The stories say that it should always be worked on at night... ideally under a new or full moon, and never during an eclipse. A red harvest moon is best. Ebony is the principal material, but at the right moment a Daedra heart must be thrown into the fire.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...